LABSON - Laboratori de Sistemes Oleohidràulics i Pneumàtics
LABSON ofereix solucions tecnològiques en el camp de l'automatització de maquinària i processos industrials. En els últims anys ha desenvolupat tecnologies com: disseny de components oleohidràulics (p.ex.: cilindres hidràulics d'altes prestacions, suspensions oli-pneumàtiques per a vehicles pesants, sistemes d'accionament de panells solars de grans dimensions, minicomponents oleohidràulics)
LABSON ha realitzat un ampli ventall de serveis que cobreixen les demandes de les empreses nacionals i internacionals. Realitza estudis teòrics i de simulació numèrica orientats a la investigació aplicada i que compta amb l'avantatge d'un fort suport experimental en l'àmbit de l'enginyeria de fluids, incloent metodologia PIV (Particle Image Velocimetry).
Collections
-
Articles de revista [21]
-
Llibres [1]
Recent Submissions
-
A review of gerotor technology in hydraulic machines
(2019-06-24)
Article
Open AccessOver the years, numerous investigations have established the gerotor fundamentals. This work aims to provide a complete review of the literature from the last decade, focusing on the articles published in the past five ... -
A novel method to determine the discharge coefficient of constant section nozzles under compressible dynamic flow conditions
(2019-07)
Article
Restricted access - publisher's policyThe present paper introduces a novel transient experimental method employed to determine the discharge coefficient of constant section nozzles of small diameters of 1 to 3 mm and with a length/diameter ratio of around one. ... -
Bond graph simulation of error propagation in position estimation of a hydraulic cylinder using low cost accelerometers
(2018-10-01)
Article
Open AccessThe indirect calculation from acceleration of transversal displacement of the piston inside the body of a double effect linear hydraulic cylinder during its operating cycle is assessed. Currently an extensive effort exists ... -
A simplified methodology to evaluate the design specifications of hydraulic components
(Multidisciplinary Digital Publishing Institute, 2018-09-11)
Article
Open AccessThe fatigue of a hydraulic component inherently varies due to various factors that can be divided into two categories: structural and load spectrum variability. The effects of both variabilities must be considered when ... -
Additioning alfa fibres in cement mortar
(Universidad Católica de Chile (UC), 2018)
Article
Open AccessCement mortar is a broadly used construction material. Adding fibres into the fresh mortar is an effective reinforcing technique to overcome the drawbacks related with the little tensile and flexural strength. Using natural ... -
Three dimensional simulation of gerotor with deforming mesh by using OpenFOAM
(2018)
Conference report
Open AccessA new-born design and construction of a mini gerotor metering pump with trochoidal-teeth is presented. The technical innovation in this new-born design is to study the fluid dynamic effects of interteeth and lateral ... -
Mechanical performance of vegetal fabric reinforced cementitious matrix (FRCM) composites
(Elsevier, 2018-06-30)
Article
Restricted access - publisher's policyIn order to pursue sustainable objectives in the construction industry, a new composite material using vegetal fibre mesh coated with resin and embedded in mortar is developed and characterized. In this study, meshes of ... -
Pressure-drop coefficients for cushioning system of hydraulic cylinder with grooved piston: a computational fluid dynamic simulation
(2017-10-25)
Article
Open AccessCushioning is an important aspect in hydraulic cylinder performance. The piston has to be decelerated before it strikes the end cap in order to avoid stresses in the cylinder components and reduce vibration that can be ... -
Magnet-sleeve-sealed mini trochoidal-gear pump prototype with polymer composite gear
(2017-09-21)
Article
Open AccessThe trochoidal-gear technology has been growing in groundbreaking fields. Forthcoming applications are demanding to this technology a step forward in the conceiving stage of positive displacement machines. The compendium ... -
Experimental study of 3D movement in cushioning of hydraulic cylinder
(2017-05-25)
Article
Open AccessA double acting cylinder operation has been fully monitored in its key functional parameters, focused on characterization of end-of-stroke cushioning and starting phases. Being the cylinder performance reliant in the piston ... -
Method for fluid flow simulation of a gerotor pump using OpenFOAM
(2017-07-21)
Article
Restricted access - publisher's policyA new approach based on the open source tool OpenFOAM is presented for the numerical simulation of a mini gerotor pump working at low pressure. The work is principally focused on the estimation of leakage flow in the ... -
Experimental study on the impulsion port of a trochoidal wheeled pump
(2017-06-01)
Article
Open AccessAll positive displacement pumps produce a pulsating flow. The present paper reports the experimental measurement of steady flow pulsations in the outlet of the internal wheeled pump. In the measured flow, the manufacturing ...