Show simple item record

dc.contributor.authorRodriguez-Calvillo, P.
dc.contributor.authorCabrera Marrero, José M.
dc.contributor.otherUniversitat Politècnica de Catalunya. Departament de Ciència dels Materials i Enginyeria Metal·lúrgica
dc.date.accessioned2015-10-28T11:39:51Z
dc.date.available2017-03-25T01:30:53Z
dc.date.issued2015-03
dc.identifier.citationRodriguez-Calvillo, P., Cabrera, J. Analysis of microstructure and strengthening in CuMg alloys deformed by equal channel angular pressing. "Journal of alloys and compounds", Març 2015, vol. 626, p. 340-348.
dc.identifier.issn0925-8388
dc.identifier.urihttp://hdl.handle.net/2117/78406
dc.description.abstractThe microstructural and strengthening behavior of two CuMg alloys, with 0.2 and 0.5 m.-% of Mg, were analyzed after severe plastic deformation by Equal Channel Angular Pressing (ECAP). Both alloys were passed through a 90° inner angle ECAP die at room temperature up to 16 passes following route Bc. The EBSD analysis of the deformed microstructure revealed a significant grain refinement after the 2nd pass. Average grain sizes as fine as 0.31 and 0.24 µm for the CuMg0.2 and CuMg0.5, respectively, were obtained after 16 passes. The tensile strength of the ECAPed samples of the present CuMg alloys did not reach a saturation level, attaining 570 and 750 MPa after 16 passes for the CuMg0.2 and CuMg0.5, respectively. The dependence of the yield stress on deformation (i.e. number of ECAP passes) and Mg content was evaluated in terms of the Hall–Petch effect (influence of grain size), dislocation density (through the subgrain hardening effect) and solid solution strengthening. Results indicated that the stronger effect comes from the subgrain microstructure rather than from High Angle Grain Boundaries (HAGB). A minor effect of the chemical composition was also noticed.
dc.format.extent9 p.
dc.language.isoeng
dc.rights.urihttp://creativecommons.org/licenses/by-nc-nd/3.0/es/
dc.subjectÀrees temàtiques de la UPC::Enginyeria dels materials
dc.subject.lcshCopper-magnesium alloys
dc.subject.otherECAP
dc.subject.otherEBSD
dc.subject.otherMechanical properties
dc.subject.otherCuMg
dc.titleAnalysis of microstructure and strengthening in CuMg alloys deformed by equal channel angular pressing
dc.typeArticle
dc.subject.lemacCoure -- Aliatges
dc.subject.lemacMagnesi -- Aliatges
dc.contributor.groupUniversitat Politècnica de Catalunya. PROCOMAME - Processos de Conformació de Materials Metàl·lics
dc.identifier.doi10.1016/j.jallcom.2014.12.043
dc.relation.publisherversionhttp://www.sciencedirect.com/science/article/pii/S0925838814029028
dc.rights.accessOpen Access
drac.iddocument16652974
dc.description.versionPostprint (author’s final draft)
upcommons.citation.authorRodriguez-Calvillo, P., Cabrera, J.
upcommons.citation.publishedtrue
upcommons.citation.publicationNameJournal of alloys and compounds
upcommons.citation.volume626
upcommons.citation.startingPage340
upcommons.citation.endingPage348


Files in this item

Thumbnail

This item appears in the following Collection(s)

Show simple item record

Except where otherwise noted, content on this work is licensed under a Creative Commons license: Attribution-NonCommercial-NoDerivs 3.0 Spain