Show simple item record

dc.contributor.authorFarré Berga, Oriol
dc.contributor.authorCercadillo Ibarguren, Iñaki
dc.contributor.authorSánchez Torres, Alba
dc.contributor.authorDomènech Mestres, Carles
dc.contributor.otherUniversitat Politècnica de Catalunya. Centre de Disseny d'Equips Industrials-Dinàmica de Màquines
dc.date.accessioned2022-04-08T09:25:28Z
dc.date.available2022-04-08T09:25:28Z
dc.date.issued2018-12-01
dc.identifier.citationFarré, O. [et al.]. Novel ball head screw and screwdriver design for implant-supported prostheses with angled channels: A finite element analysis. "The journal of oral implantology", 1 Desembre 2018, vol. 44, núm. 6, p. 416-422.
dc.identifier.issn0160-6972
dc.identifier.urihttp://hdl.handle.net/2117/365556
dc.description.abstractThe primary objective of this study was to design the optimal geometry of a novel screwdriver, create the grooves on a ball head screw, and demonstrate its resistance to a torque of up to 40 Ncm at angulations of 0°, 15°, and 30° by using nonlinear finite element analysis. A secondary objective was to create a foolproof, easily recognizable system. The grooved ball head screw and geometry of the screwdriver, functioning from an angulation of 0° to 30°, was generated using Pro-ENGINEER Wildfire 5.0 software. Static structural analyses among bodies in contact were performed at different angles of 0°, 15°, and 30° at a torque of 20 Ncm and 40 Ncm using nonlinear finite element simulation by means of ANSYS 12.0. The maximum stress supported by the ball head screw and screwdriver was similar at 20 Ncm and 40 Ncm. Although greater deformations were found at 40 Ncm, these were small and might not affect the performance of the system. Further, the rupture torque value for the M2 connection was 55 Ncm for 0° and 30°, and 47.5 Ncm for 15°. Numerical simulation showed that the ball head system design can achieve the mechanical strength requirements expected for screws used in implant-supported restorations at an angulation of up to 30°. Finite element analysis showed this novel ball head screw and screwdriver system to be a good solution for angled screw channels in implant-supported prostheses.
dc.format.extent7 p.
dc.language.isoeng
dc.rightsAttribution-NonCommercial-NoDerivs 3.0 Spain
dc.rights.urihttp://creativecommons.org/licenses/by-nc-nd/3.0/es/
dc.subject.lcshImplant dentures
dc.titleNovel ball head screw and screwdriver design for implant-supported prostheses with angled channels: A finite element analysis
dc.typeArticle
dc.subject.lemacImplants dentals
dc.contributor.groupUniversitat Politècnica de Catalunya. CDEI-DM - Centre de Disseny d'Equips Industrials-Dinàmica de Màquines
dc.identifier.doi10.1563/aaid-joi-D-18-00103
dc.relation.publisherversionhttps://www.joionline.org/doi/10.1563/aaid-joi-D-18-00103
dc.rights.accessOpen Access
local.identifier.drac23658819
dc.description.versionPostprint (published version)
local.citation.authorFarré, O.; Cercadillo, I.; Sánchez, A.; Domenech, C.
local.citation.publicationNameThe journal of oral implantology
local.citation.volume44
local.citation.number6
local.citation.startingPage416
local.citation.endingPage422


Files in this item

Thumbnail

This item appears in the following Collection(s)

Show simple item record