Mostra el registre d'ítem simple

Reinforced photocurable materials for an Additive Manufacturing process based on Mask Image Projection

dc.contributor.authorBonada Bo, Jordi
dc.contributor.authorXuriguera Martin, Elena
dc.contributor.authorMuguruza Blanco, Asier
dc.contributor.authorGonçalves, Joana
dc.contributor.authorBarcelona, Pol
dc.contributor.authorPons Poblet, Josep Maria
dc.contributor.authorMinguella Canela, Joaquim
dc.contributor.authorUceda Molera, Roger
dc.contributor.otherUniversitat Politècnica de Catalunya. Departament de Resistència de Materials i Estructures a l'Enginyeria
dc.contributor.otherUniversitat Politècnica de Catalunya. Doctorat en Enginyeria Mecànica, Fluids i Aeronàutica
dc.contributor.otherUniversitat Politècnica de Catalunya. Departament d'Enginyeria Mecànica
dc.date.accessioned2020-03-19T08:43:29Z
dc.date.available2020-03-19T08:43:29Z
dc.date.issued2020-03-09
dc.identifier.citationBonada, J. [et al.]. Reinforced photocurable materials for an Additive Manufacturing process based on Mask Image Projection. "Procedia manufacturing", 9 Març 2020, vol. 41, p. 531-538.
dc.identifier.issn2351-9789
dc.identifier.urihttp://hdl.handle.net/2117/180480
dc.description.abstractMask Image Projection based on Stereolithography (MIP-SL) is an Additive Manufacturing (AM) system which it is based on a Frontal Photopolymerization Process (FPP) to manufacture parts made of photocurable materials. In this paper, a FPP numerical model is used to analyse the printability of different reinforced photocurable materials for MIP-SL manufacturing process. Consequently, optimal printing parameters could be defined to increase the material photoconversion ratio. Two different reinforcements are used to analyse the influence of fillers on FPP material coefficients. The results show the use of reinforcement could significantly enhance the mechanical properties obtained by means of experimental compression tests
dc.format.extent8 p.
dc.language.isoeng
dc.rightsAttribution-NonCommercial-NoDerivs 3.0 Spain
dc.rights.urihttp://creativecommons.org/licenses/by-nc-nd/3.0/es/
dc.subjectÀrees temàtiques de la UPC::Enginyeria mecànica
dc.subject.lcshMaterials -- Mechanical properties
dc.subject.lcshThree-dimensional printing
dc.subject.otherAdditive Manufacturing
dc.subject.otherMask Image Projection
dc.subject.otherMechanical properties
dc.subject.otherReinforced materials
dc.titleReinforced photocurable materials for an Additive Manufacturing process based on Mask Image Projection
dc.typeArticle
dc.subject.lemacMaterials -- Propietats mecàniques
dc.subject.lemacImpressió 3D
dc.contributor.groupUniversitat Politècnica de Catalunya. REMM - Recerca en Estructures i Mecànica de Materials
dc.contributor.groupUniversitat Politècnica de Catalunya. TECNOFAB - Grup de Recerca en Tecnologies de Fabricació
dc.identifier.doi10.1016/j.promfg.2019.09.040
dc.description.peerreviewedPeer Reviewed
dc.relation.publisherversionhttps://www.sciencedirect.com/science/article/pii/S2351978919311291
dc.rights.accessOpen Access
local.identifier.drac27256712
dc.description.versionPostprint (published version)
local.citation.authorBonada, J.; Xuriguera, E.; Muguruza, A.; Gonçalves, J.; Barcelona, P.; Pons, J.Mª; Minguella-Canela, J.; Uceda, R.
local.citation.publicationNameProcedia manufacturing
local.citation.volume41
local.citation.startingPage531
local.citation.endingPage538


Fitxers d'aquest items

Thumbnail
Nom:
1-s2.0-S2351978919311291-main.pdf
Mida:
784,0Kb
Format:
PDF
Visualitza/Obre

Aquest ítem apareix a les col·leccions següents

Mostra el registre d'ítem simple