Show simple item record

dc.contributor.authorHameed, Saqib
dc.contributor.authorGonzález Rojas, Hernan Alberto
dc.contributor.authorPerat Benavides, Josep Ignasi
dc.contributor.authorNápoles Alberro, Amelia
dc.contributor.authorSánchez Egea, Antonio J
dc.contributor.otherUniversitat Politècnica de Catalunya. Departament d'Enginyeria Mecànica
dc.contributor.otherUniversitat Politècnica de Catalunya. Departament d'Enginyeria Elèctrica
dc.date.accessioned2018-06-01T07:53:46Z
dc.date.available2018-06-01T07:53:46Z
dc.date.issued2018-05-25
dc.identifier.citationHameed, S., Gonzalez-Rojas, Hernan A., Perat, J., Napoles, A., Sánchez, A. Influence of the regime of electropulsing-assisted machining on the plastic deformation of the layer being cut. "Materials", 25 Maig 2018, vol. 11, núm. 6, p. 886-1 - 886-10.
dc.identifier.issn1996-1944
dc.identifier.otherhttps://www.terkko.helsinki.fi/article/18779231_materials-vol-11-pages-886-influence-of-the-regime-of-electropulsing-assisted-machining-on-the-plastic-deformation-of-the-layer-being-cut
dc.identifier.urihttp://hdl.handle.net/2117/117696
dc.description.abstractIn this article, the influence of electropulsing on the machinability of steel S235 and aluminium 6060 has been studied during conventional and electropulsing-assisted turning processes. The machinability indices such as chip compression ratio ¿, shear plane angle f and specific cutting energy (SCE) are investigated by using different cutting parameters such as cutting speed, cutting feed and depth of cut during electrically-assisted turning process. The results and analysis of this work indicated that the electrically-assisted turning process improves the machinability of steel S235, whereas the machinability of aluminium 6060 gets worse. Finally, due to electropluses (EPs), the chip compression ratio ¿ increases with the increase in cutting speed during turning of aluminium 6060 and the SCE decreases during turning of steel S235.
dc.language.isoeng
dc.rightsAttribution 4.0 International
dc.rights.urihttps://creativecommons.org/licenses/by/4.0/
dc.subjectÀrees temàtiques de la UPC::Enginyeria mecànica::Processos de fabricació mecànica
dc.subjectÀrees temàtiques de la UPC::Enginyeria elèctrica
dc.subject.lcshTurning
dc.subject.otherElectropulsing
dc.subject.otherMachinability
dc.subject.otherChip compression ratio
dc.subject.otherCurrent density
dc.subject.otherSpecific cutting energy
dc.titleInfluence of the regime of electropulsing-assisted machining on the plastic deformation of the layer being cut
dc.typeArticle
dc.subject.lemacTorns mecànics
dc.contributor.groupUniversitat Politècnica de Catalunya. GAECE - Grup d'Accionaments Elèctrics amb Commutació Electrònica
dc.contributor.groupUniversitat Politècnica de Catalunya. TECNOFAB - Grup de Recerca en Tecnologies de Fabricació
dc.identifier.doi10.3390/ma11060886
dc.description.peerreviewedPeer Reviewed
dc.relation.publisherversionhttp://www.mdpi.com/1996-1944/11/6/886
dc.rights.accessOpen Access
drac.iddocument22958077
dc.description.versionPostprint (published version)
upcommons.citation.authorHameed, S., Gonzalez-Rojas, Hernan A., Perat, J., Napoles, A., Sánchez, A.
upcommons.citation.publishedtrue
upcommons.citation.publicationNameMaterials
upcommons.citation.volume11
upcommons.citation.number6
upcommons.citation.startingPage886-1
upcommons.citation.endingPage886-10


Files in this item

Thumbnail

This item appears in the following Collection(s)

Show simple item record

Except where otherwise noted, content on this work is licensed under a Creative Commons license: Attribution 4.0 Generic