Show simple item record

dc.contributor.authorPáramo-Kañetas, Pedro
dc.contributor.authorOzturk, Utkudeniz
dc.contributor.authorCalvo Muñoz, Jessica
dc.contributor.authorCabrera Marrero, José M.
dc.contributor.authorGuerrero Mata, Martha P.
dc.contributor.otherUniversitat Politècnica de Catalunya. Departament de Ciència dels Materials i Enginyeria Metal·lúrgica
dc.date.accessioned2018-02-28T06:39:35Z
dc.date.available2020-05-01T00:25:52Z
dc.date.issued2018-05-01
dc.identifier.citationPáramo-Kañetas, P., Ozturk, U., Calvo, J., Cabrera, J., Guerrero, M. High-temperature deformation of delta-processed Inconel 718. "Journal of materials processing technology", 1 Maig 2018, vol. 255, p. 204-211.
dc.identifier.issn0924-0136
dc.identifier.urihttp://hdl.handle.net/2117/114578
dc.description.abstract© 2017 Elsevier B.V. The hot-flow behavior of Inconel 718 subjected to delta processing (DP) was analyzed. Hot compression tests were subsequently performed at 960 °C and 1020 °C at the four different strain rates of 0.001, 0.01, 0.1, and 1 s-1. The two deformation temperatures were located below and above the d-solvus of IN718 respectively. Microstructural characterization was performed by means of optical (OM) and scanning electron microscopy (SEM). The high temperature deformation results in the fragmentation of the existing d-phase by means of partial dissolution and/or deformation, leading to an improved grain size control. A classic dynamic recrystallization (DRX) behavior was observed in the flow curves, which is typical of low-medium stacking fault energy (SFE) alloys. This flow behavior was modeled according to various approaches. Peak stress modeling was performed using two different approaches, referred to as ‘apparent’ and ‘physically-based’. The hot-flow behavior before the peak stress was modeled according to the Estrin-Mecking-Bergstrom approach, with Avrami kinetics employed to describe the DRX behavior.
dc.format.extent8 p.
dc.language.isoeng
dc.rightsAttribution-NonCommercial-NoDerivs 3.0 Spain
dc.rights.urihttp://creativecommons.org/licenses/by-nc-nd/3.0/es/
dc.subjectÀrees temàtiques de la UPC::Enginyeria dels materials
dc.subject.lcshHeat resistant materials
dc.subject.otherDelta processing
dc.subject.otherInconel 718
dc.subject.otherphysically-based approach
dc.titleHigh-temperature deformation of delta-processed Inconel 718
dc.typeArticle
dc.subject.lemacInconel
dc.contributor.groupUniversitat Politècnica de Catalunya. PROCOMAME - Processos de Conformació de Materials Metàl·lics
dc.identifier.doi10.1016/j.jmatprotec.2017.12.014
dc.description.peerreviewedPeer Reviewed
dc.relation.publisherversionhttp://www.sciencedirect.com/science/article/pii/S0924013617305976?via%3Dihub
dc.rights.accessOpen Access
local.identifier.drac21706131
dc.description.versionPostprint (author's final draft)
local.citation.authorPáramo-Kañetas, P.; Ozturk, U.; Calvo, J.; Cabrera, J.; Guerrero, M.
local.citation.publicationNameJournal of materials processing technology
local.citation.volume255
local.citation.startingPage204
local.citation.endingPage211


Files in this item

Thumbnail

This item appears in the following Collection(s)

Show simple item record

Attribution-NonCommercial-NoDerivs 3.0 Spain
Except where otherwise noted, content on this work is licensed under a Creative Commons license : Attribution-NonCommercial-NoDerivs 3.0 Spain