Màster universitari en Enginyeria Mecànica - EMMME
Envíos recientes
-
Design of a Gearbox for an electric FSAE vehicle
(Universitat Politècnica de Catalunya / Illinois Institute of Technology, 2016-06)
Projecte Final de Màster Oficial
Acceso abiertoThe main objective of this project is to design a new gearbox for an electric Formula SAE car. The last car had one motor for each wheel, and for the new car, only one motor will be used to give traction to the rear ... -
Cost analysis of the UGEN
(Universitat Politècnica de Catalunya / Instituto Superior Técnico, 2016-09)
Projecte Final de Màster Oficial
Acceso abierto
Realizado en/con: Instituto Superior Técnico LisboaThe world energy consumption is estimated to increase considerably over the next decades. In the dynamic evolution of the renewable energy sector, a wave energy industry is emerging. Although wave energy technologies are ... -
Design of a vibration isolation system for reducing the vibration level in mobile robot
(Universitat Politècnica de Catalunya, 2016-02)
Projecte Final de Màster Oficial
Acceso abiertoThis thesis focuses on the problem of passive vibration isolation applied to a mobile robot. The aims of the project are to analyse the disturbances that afflict the mobile robot and to develop a passive vibration isolation ... -
Numerical simulation of condensation in a supersonic nozzle for application to ejectors in refrigeration
(Universitat Politècnica de Catalunya / Université catholique de Louvain, 2014)
Projecte Final de Màster Oficial
Acceso abiertoThis thesis is a CFD study of a supersonic nozzle for ejector refrigeration applications. Condensation of the working uid is aimed inside the nozzle in order to study its conse- quences. As a first approach to verify ... -
Design of an adaptive brake pressure controller for the antilock braking system
(Universitat Politècnica de Catalunya / Technische Universiteit Delft, 2013)
Proyecto final de máster UPC
Acceso restringido por decisión del autorIn the past few decades, the introduction of electronics in motor vehicles has marked its development. At the beginning, electronic systems were used to control the engine (electronic fuel-injection systems). From that ... -
Design and manufacturing of the Nub3d Sidio inspect body
(Universitat Politècnica de Catalunya, 2012-06)
Projecte Final de Màster Oficial
Acceso restringido por decisión del autorThis final Project has involved the redesigning and manufacturing of the body of a 3D scanner called Sidio Inspect. The main components of this scanner are the projector, a camera along with all the necessary hardware to ... -
Estudio de la evolución de la rugosidad en un proceso de pulido de una superficie rectificada
(Universitat Politècnica de Catalunya, 2012-10)
Projecte Final de Màster Oficial
Acceso restringido por decisión del autorEn el presente trabajo fin de máster se ha estudiado la evolución de la rugosidad superficial de un acero para moldes, que se ha rectificado bajo diferentes condiciones y posteriormente se ha sometido a sucesivos procesos ... -
Evaluation of the method: Computational modeling of Jominy test with variable thermal properties using finite elements
(Universitat Politècnica de Catalunya, 2011-09)
Projecte Final de Màster Oficial
Acceso restringido por decisión del autorWith the introduction of numerical methods, combined with powerful computational resources, a larger amount of problems of higher complexity could be solved compared to those solved by analytical methods. Analytical ... -
Desarrollo de metodología para evaluación mecánica de una junta soldada en "T"
(Universitat Politècnica de Catalunya, 2008-06)
Projecte Final de Màster Oficial
Acceso restringido por decisión del autorSe realizó el estudio del comportamiento mecánico de una unión soldada en “T” con láminas de acero UNE F1 utilizando electrodos revestidos AWS E-6013 con la finalidad de realizar un aporte en referencia a los procedimientos ... -
Application of reverse engineering concepts to compressed air tank
(Universitat Politècnica de Catalunya, 2010-06)
Projecte Final de Màster Oficial
Acceso restringido por decisión del autorThis study, application of reverse engineering concepts to a compressed air tank, leads us to calculate tank shell in static and fatigue, by using of formulas and software. Furthermore, unsatisfying results from basics ... -
Practical issue for a new identification method of Hammerstein system
(Universitat Politècnica de Catalunya, 2010-06)
Projecte Final de Màster Oficial
Acceso restringido por decisión del autorThe Hammerstein and Wiener models are nonlinear representations od systems composed by the coupling of a static nonlinearity N and a linear system L in the form N-L (Hammerstein) and L-N (Wiener). Although the forms are ... -
Design of the manufacturing process of a reduction gear
(Universitat Politècnica de Catalunya, 2010-06)
Projecte Final de Màster Oficial
Acceso restringido por decisión del autorThe purpose of this project entitled “Design of the manufacturing process of a reduction gear” is to design a manufacturing process in order to produce 20000 units of a reduction gear per year. It is enrolled for a ...
RSS 1.0