Browsing by Subject "Prototypes, Engineering"
Now showing items 1-20 of 72
-
A proportional plus a hysteretic term control design: a throttle experimental emulation to wind turbines pitch control
(2019-05-22)
Article
Open AccessPitch control is a relevant issue in wind turbines to properly operate the angle of the blades. Therefore, this control system pitches the blades usually a few degrees every time the wind changes in order to keep the rotor ... -
Análisis, estudio y optimización del conjunto motor, inversor y bateria de una motocicleta de competición
(Universitat Politècnica de Catalunya, 2018-05-10)
Bachelor thesis
Restricted access - author's decisionEste proyecto se enmarca dentro de la construcción de un prototipo de motocicleta eléctrica de competición por parte del equipo universitario de la facultad de Tarrasa, MotoSpirit UPC que participó en la competición ... -
BESPA: the design and manufacturing of a 2 wheeled self balancing scooter prototype
(Universitat Politècnica de Catalunya, 2015-06)
Bachelor thesis
Restricted access - author's decision
Covenantee: Ecole Nationale d'Ingénieurs de TarbesThe project has as objective the design, development and making of a prototype of a self-balancing electrical scooter for the mechanical department of the Ecole Nationale d’Ingénieurs of Tarbes. As this is a project build ... -
Characterization of test results of the performance of additive manufacturing parts obtained by selective laser sintering processes incorporating glass and carbon fibres
(2012)
Conference lecture
Restricted access - publisher's policySelective Laser Sintering, and in general Additive Manufacturing Processes are becoming mature technologies; in the sense that after many years of market introduction there are some well-known manufacturers that provide ... -
Control d' un sistema de dipòsits desacoblats.
(Universitat Politècnica de Catalunya, 2015)
Bachelor thesis
Open AccessEn aquest projecte es realitza el disseny i construcció del prototip d’un sistema de dipòsits desacoblats. Amb aquesta implementació es pretén millorar l’antiga maqueta que hi havia al Laboratori de control per un posterior ... -
Controllers implementation in low-cost platforms
(Universitat Politècnica de Catalunya, 2023-01-25)
Bachelor thesis
Open AccessL’objectiu d’aquest treball és implementar un controlador en una placa basada en Arduino per controlar una maqueta del sistema ball and beam i desenvolupar una documentació que pugui ajudar estudiants tant del Grau com del ... -
De les MATES al STEAM : conclusions i actuacions desenvolupades a la E.T.S. d’Enginyeria de Camins, Canals i Ports
(Universitat Politècnica de Catalunya. Institut de Ciències de l'Educació, 2022-05)
Article
Open AccessAquest article descriu els resultats del projecte “de las MATES al STEAM”, el qual es va completar durant els anys 2019 a 2021 a la E.T.S. d’Enginyeria de Camins, Canals i Ports. L'objectiu inicial del projecte era ... -
Design of a prototype for the in situ forming of a liquid infused preform (ISFLIP) process
(2020-01)
Article
Open AccessThe world is changing and demanding stronger, lighter and more versatile materials. Taking advantage of the full potential of these materials also requires versatile manufacturing processes. The in situ forming of a liquid ... -
Design project of a plastic grab handle
(Universitat Politècnica de Catalunya, 2016-06)
Bachelor thesis
Restricted access - author's decisionWith the title of “Design project of a plastic grab handle” it will perform a grab handle prototype with the experience of the study of the different grab handle which Nifco has. That is to say, in other words, the aim ... -
Development of a patients-specific 3D-printed preoperative planning and training tool, with functionalized internal surfaces, for complex oncologic cases
(2019)
Article
Restricted access - publisher's policyThe use of physical 3D models has been used in the industry for a while, fulfilling the function of prototypes in the majority of cases where the designers, engineers and manufacturers optimize their designs before taking ... -
Diseño de andamios paramétricos con porosidad variable e interconectada para ingeniería de tejidos óseos
(OmniaScience, 2022-02-01)
Conference lecture
Open AccessSe proponen nuevos métodos de diseño de andamios porosos a partir de la aplicación de software de libre uso Grasshopper© de Rhinoceros 3D con el objetivo de diseñar modelos con porosidad variable e interconectada semejante ... -
Diseño de carcasa para control de presencia
(Universitat Politècnica de Catalunya, 2005-05)
Master thesis (pre-Bologna period)
Restricted access - author's decision
Covenantee: Fundació CIMEl proyecto documentado a continuación es un diseño realizado para el mercado actual. Se ha realizado en el Centro CIM, dentro del departamento de Ingeniería y se trata del diseño de una carcasa de control de presencia. El ... -
Diseño de carro móvil para montaña rusa
(Universitat Politècnica de Catalunya, 2020-01)
Bachelor thesis
Restricted access - confidentiality agreement -
Diseño de un sistema de seguridad para equipaje en trenes de alta velocidad
(Universitat Politècnica de Catalunya, 2017-01)
Bachelor thesis
Restricted access - author's decision
Covenantee: AlstomEste proyecto tiene como objetivo el diseño de una carcasa para un sistema de seguridad que pretende ser instalado en trenes de alta velocidad. Alstom, una empresa que realiza todo tipo de actividades relacionadas con el ... -
Diseño de una solución integral para invidentes
(Universitat Politècnica de Catalunya, 2021-06-22)
Bachelor thesis
Open AccessDiseño de una solución integral para invidentes: Se ha trabajado la problemática de las personas con discapacitadas visuales encontrando cuál es su mayor escollo en el día a día y se ha trabajado una solución para mejorar ... -
Diseño mecanico y prototipado de dosimetros neutronicos LINrem
(Universitat Politècnica de Catalunya, 2021-06-05)
Bachelor thesis
Restricted access - author's decisionEl treball consisteix a implementar sistemes al disseny conceptual del dosímetre de neutrons LINrem 2 per facilitar la seva utilització, millorar la seva robustesa i permetre que es prossegueixi amb la seva homologació ... -
Diseño modular y prototipado de impresoras 3D
(Universitat Politècnica de Catalunya, 2018-10)
Bachelor thesis
Restricted access - author's decision -
Disseny d'un equip multifunció per a prototipatge digital
(Universitat Politècnica de Catalunya, 2017-07)
Bachelor thesis
Restricted access - author's decisionAquest treball es basa en el desenvolupament i disseny d’un equip multifunció per a prototipatge digital, el qual incorpora més d’un eina. L’objectiu principal d’aquest projecte és minimitzar l’espai dedicat per a l’usuari ... -
Disseny d'un patinet elèctric
(Universitat Politècnica de Catalunya, 2022-07-18)
Bachelor thesis
Open AccessL’objectiu d’aquest projecte és el de dissenyar i confeccionar un patinet elèctric. Actualment la mobilitat urbana sostenible està en ple desenvolupament com a conseqüència de les ultimes regulacions mediambientals i el ...