Browsing by Subject "Inconel"
Now showing items 1-12 of 12
-
3D Printing of Inconel 718 by MEAM
(Universitat Politècnica de Catalunya, 2021-02-08)
Master thesis
Open AccessLa fabricación aditiva es una técnica de fabricación en plena expansión. Sin embargo, la técnica de modelado de deposición fundida no está muy desarrollada para los metales. El objetivo de este proyecto es encontrar el ... -
3D Printing of Inconel 718 by Meam (Metal Extrussion Additive Manufacturing)
(Universitat Politècnica de Catalunya, 2022-02-10)
Master thesis
Open AccessMentre que en els últims anys s'ha avançat molt en la distribució de tecnologies d'impressió 3D com FDM, poc s’ha avançat en solucions de baix cost per utilitzar metalls mitjançant la fabricació additiva. L'objectiu ... -
Analysis of the part distortions for inconel 718 SLM: a case study on the NIST test artifact
(Multidisciplinary Digital Publishing Institute (MDPI), 2020-11-11)
Article
Open AccessThe present paper evaluates the misalignment and geometry distortion of the standard National Institute of Standards and Technology (NIST) test artifact in Inconel 718 alloy, when several layers with and without supports ... -
Characterization of precipitation kinetics of Inconel 718 superalloy by the stress relaxation technique
(2012)
Article
Restricted access - publisher's policyInconel 718 is a nickel-chromium-iron superalloy which presents excellent mechanical properties at high temperatures, as well as good corrosion resistance and weldability. These characteristics can be optimized with an ... -
Characterization of strain-induced precipitation in Inconel 718 superalloy
(2016-06-15)
Article
Open Access© 2016 ASM International Inconel 718 presents excellent mechanical properties at high temperatures, as well as good corrosion resistance and weldability. These properties, oriented to satisfy the design requirements of gas ... -
Dynamic recrystallization mechanisms and twining evolution during hot deformation of Inconel 718
(2016-12-15)
Article
Open AccessThe hot deformation behavior of an IN718 superalloy was studied by isothermal compression tests under the deformation temperature range of 950–1100 °C and strain rate range of 0.001–1 s-1 up to true strains of 0.05, 0.2, ... -
Estudi de la corrosió d'Inconel® 600 en sulfat de sodi fos a 899ºC.
(Universitat Politècnica de Catalunya / Escola Tècnica Superior d’Enginyeria Industrial de Barcelona, 2009-03)
Master thesis (pre-Bologna period)
Open AccessL'aliatge Inconel® 600 esta dissenyada específicament per resistir ambients corrosius a altes temperatures. El sulfat de sodi fos es un possible candidat per actuat com a material per l’emmagatzemament d'energia per calor ... -
Fabricación y caracterización de Componentes de Inconel 718 producidos mediante manufactura aditiva basada en la extrusión usando pellets de moldeo por inyección metálica
(Universitat Politècnica de Catalunya, 2020-07-14)
Bachelor thesis
Open AccessLa manufactura aditiva (AM) se define como el proceso de unión de materiales capa a capa para fabricar objetos tridimensionales. Recientemente ha aparecido una tecnología AM conocida como MEAM-HP (Material Extrusion ... -
High-temperature deformation of delta-processed Inconel 718
(2018-05-01)
Article
Open Access© 2017 Elsevier B.V. The hot-flow behavior of Inconel 718 subjected to delta processing (DP) was analyzed. Hot compression tests were subsequently performed at 960 °C and 1020 °C at the four different strain rates of 0.001, ... -
High-temperature deformation of Inconel 718Plus (TM)
(2017-03-01)
Article
Restricted access - publisher's policySince its introduction in 2003, alloy 718PlusTM spurred a lot of interest owing to its increased maximum service temperature over conventional Inconel 718 (704¿°C versus 650¿°C), good formability, and weldability together ... -
The impact of additive manufacturing on micro-turbine ports
(Universitat Politècnica de Catalunya / Cranfield University, 2017-09)
Master thesis
Open AccessIn the coming years, Additive Manufacturing will play an increasingly role in micro-turbine production, therefore the importance to know the impact of this type of manufacturing are crucial for the optimum design and ... -
The use of hybrid CO2+MQL in machining operations
(2015)
Conference report
Restricted access - publisher's policyNowadays, the environmental concern in machining industry is a fact. Because of that, in this article a new cooling-lubrication system which combines CO2 cryogenic and MQL technologies is presented. The aim of this new ...