Atmospheric boundary layer height estimation using combined microwave radiometer and lidar data
Visualitza/Obre
Atmospheric Boundary Layer Height Estimation using Combined Microwave Radiometer and Lidar data (234,0Kb) (Accés restringit)
Sol·licita una còpia a l'autor
Què és aquest botó?
Aquest botó permet demanar una còpia d'un document restringit a l'autor. Es mostra quan:
- Disposem del correu electrònic de l'autor
- El document té una mida inferior a 20 Mb
- Es tracta d'un document d'accés restringit per decisió de l'autor o d'un document d'accés restringit per política de l'editorial
atmospheric boundary.pdf (63,03Kb) (Accés restringit)
Sol·licita una còpia a l'autor
Què és aquest botó?
Aquest botó permet demanar una còpia d'un document restringit a l'autor. Es mostra quan:
- Disposem del correu electrònic de l'autor
- El document té una mida inferior a 20 Mb
- Es tracta d'un document d'accés restringit per decisió de l'autor o d'un document d'accés restringit per política de l'editorial
Estadístiques de LA Referencia / Recolecta
Inclou dades d'ús des de 2022
Cita com:
hdl:2117/27953
Tipus de documentComunicació de congrés
Data publicació2014
Condicions d'accésAccés restringit per política de l'editorial
Tots els drets reservats. Aquesta obra està protegida pels drets de propietat intel·lectual i
industrial corresponents. Sense perjudici de les exempcions legals existents, queda prohibida la seva
reproducció, distribució, comunicació pública o transformació sense l'autorització del titular dels drets
Abstract
The estimation of atmospheric boundary layer height (ABLH) during a full diurnal cycle using ground-based remote sensing instruments is one of the key challenges in atmospheric science. Most of these instruments such as the lidar, the microwave radiometer (MWR), the radar, and the sodar measure one of the physical parameters, i.e., temperature, aerosol concentration, wind speed, and heat flux, within the Atmospheric Boundary Layer (ABL).
All these instruments, while performing well under specific atmospheric conditions, are limited in others. Thus, an estimate of the ABLH based on the lidar return signal alone is quite good under convective conditions, where there is a clear interface between a well-mixed concentration of aerosols in the mixing layer (ML) and the free troposphere (FT). In contrast, in night-time conditions, when the convective ML recedes and a stable boundary layer (SBL) develops near the surface of the Earth, the lidar backscattered signal is usually insufficient to resolve the SBL. Similarly, a MWR is limited by its poor range resolution.
In this context, a MWR-ceilometer combination is proposed. Temperature-inversion retrievals from the MWR, containing the approximate height range where the SBL is located, roughly guide the Kalman Filter based ABLH estimation algorithm for the lidar return signal, hence resulting in acceptably accurate estimates of the ABLH.
The proposed approach is applied to collocated ceilometer-MWR instruments under the simple ”clear-atmosphere” cases. Radiosonde data, whenever available, is used as a reference or ”physical truth”.
CitacióSaeed, U. [et al.]. Atmospheric boundary layer height estimation using combined microwave radiometer and lidar data. A: World Weather Open Science Conference. "World Weather Open Science Conference 2014: August 16-21, 2014, Montréal, Canada: abstracts". Montreal: 2014, p. 799.
Fitxers | Descripció | Mida | Format | Visualitza |
---|---|---|---|---|
WWOSC_Montreal_20140816_UM_poster.pdf | Atmospheric Boundary Layer Height Estimation using Combined Microwave Radiometer and Lidar data | 234,0Kb | Accés restringit | |
atmospheric boundary.pdf | 63,03Kb | Accés restringit |