Exploració per autor "Cabrera Marrero, José M."
Ara es mostren els items 13-32 de 196
-
Breve historia del temple: de las espadas a los automóviles modernos
Ocaña Ruiz, Helios; González Reyes, José Gonzalo; Cabrera Marrero, José M. (2022-09)
Article
Accés obert -
Calorimetric analysis of a Mg-Zn-Zr alloy processed by equal channel angular pressing via route A
Dumitru, Florina Diana; Ghiban, Brândusa; Cabrera Marrero, José M.; Higuera Cobos, Oscar Fabián; Gurau, Gheorghe; Ghiban, Nicolae (2014)
Article
Accés restringit per política de l'editorialBeing the lightest structural element, magnesium a nd its alloys has attracted significant interest in the last years, but because of its hexa gonal close packed structure, magnesium presents relatively low strength ... -
Caracteristicas de la deformacion en caliente de aceros TWIP
Calvo Muñoz, Jessica; Rodríguez Calvillo, Pablo; Cabrera Marrero, José M.; Mateo García, Antonio Manuel (2012)
Text en actes de congrés
Accés obert -
Caracterización mecánico-metalúrgica de la conformación en caliente del acero microaleado de medio carbono 38 MnSiVS5
Cabrera Marrero, José M. (Universitat Politècnica de Catalunya, 1995-10-23)
Tesi
Accés obertEn el presente trabajo de investigación se estudia el comportamiento durante un proceso de termoconformado de un acero microaleado comercial de medio carbono. Debido a la persistente falta de tenacidad de estos aceros se ... -
Characterization of a Gas Tungsten Arc Welding (GTAW) joint of Armco iron nanostructured by equal-channel angular pressing (ECAP)
Mejía Granados, Ignacio; Cabrera Marrero, José M. (2021-02)
Article
Accés obertAfter Severe Plastic Deformation (SPD), the strength of the Armco iron sharply increases with the number of Equal-Channel Angular Pressing (ECAP) passes. So, the ultimate tensile stress (UTS) reached up to 800¿MPa after ... -
Characterization of bimetallic interface in Cu-Al and Ni-Cu rods cold-welded by ECAP
Zhilyaev, Alexander P.; Werner, Thomas; Cabrera Marrero, José M. (2019-11-23)
Article
Accés obertWhile cold welding by equal channel angular pressing has already been confirmed to be a viable alternative to join materials that commonly tend to exhibit unwanted brittleness and other heat-induced properties, the exact ... -
Characterization of inclusions and second-phase particles in high-Mn TWIP steels microalloyed with Ti, Ti/B, Nb, V, Mo, in as-solutioned condition
Mijangos Espinosa, David; Mejía Granados, Ignacio; Cabrera Marrero, José M. (Cambridge University Press, 2020-10-22)
Article
Accés obertIn recent years there has been an increase in the field of research of advanced steels that have excellent mechanical properties combining high strength with excellent ductility. Within this range of advanced steels are ... -
Characterization of microstructure and texture of binary Mg-Ce alloy processed by equal channel angular pressing
Sadi, Salaheddine; Hanna, Abdelkader; Azzeddine, Hiba; Casas Quesada, Casimir; Baudin, Thierry; Helbert, Anne-Laure; Brisset, François; Cabrera Marrero, José M. (2021-11-01)
Article
Accés obertThe characterization of microstructure and texture development of binary Mg-0.3Ce (wt%) after equal-channel angular pressing (ECAP) processing via route Bc at 300 and 350 °C through 4 passes were investigated using electron ... -
Characterization of precipitation kinetics of Inconel 718 superalloy by the stress relaxation technique
Calvo Muñoz, Jessica; Cabrera Marrero, José M.; Shu, Sheyu (2012)
Article
Accés restringit per política de l'editorialInconel 718 is a nickel-chromium-iron superalloy which presents excellent mechanical properties at high temperatures, as well as good corrosion resistance and weldability. These characteristics can be optimized with an ... -
Characterization of strain-induced precipitation in Inconel 718 superalloy
Calvo Muñoz, Jessica; Penalva, Mariluz; Cabrera Marrero, José M. (2016-06-15)
Article
Accés obert© 2016 ASM International Inconel 718 presents excellent mechanical properties at high temperatures, as well as good corrosion resistance and weldability. These properties, oriented to satisfy the design requirements of gas ... -
Cobre nanocristalino y ultrafino obtenido por molienda mecánica
Rodríguez Baracaldo, R.; Benito Páramo, José Antonio; Cabrera Marrero, José M. (2010)
Article
Accés restringit per política de l'editorialEste artículo presenta un método de obtención y caracterización de muestras masivas de cobre con tamaño de grano ultrafino (inferior a 1 μm) y nanocristalino (inferior a 100 nm). La fabricación del cobre se realiza ... -
Comportamiento termomecánico de un acero microaleado al Nb-V
Cartaya, E. A.; Varela, G.; Cabrera Marrero, José M.; Prado Pozuelo, José Manuel (2012-06)
Article
Accés obertEmpleando ensayos de compresión simple en ca- liente y relajación de tensiones después de la de - formación en un dilatómetro modelo DIL805T, se obtuvieron las curvas de fluencia y relajación de dos aceros, el primero ... -
Computational simulation of thermo-mechanical field and fluid flow and their effect on the solidification process in TWIP steel welds
García García, Víctor; Mejía, Ignacio; Hernández Belmontes, Humberto; Reyes Calderón, Francisco; Benito Páramo, José Antonio; Cabrera Marrero, José M. (Elsevier, 2022-12-01)
Article
Accés obertThe primary austenitic solidification mode of Twinning Induced Plasticity (TWIP) steel weld joints is one of the most important issues limiting its weldability. In order to gain knowledge on this topic, a comprehensive ... -
Consolidation of AA7075-2wt%ZrO2 composite powders by severe plastic deformation via ECAP
Hernadez-Martinez, S. E.; Cruz-Rivera, J. J.; Martinez-Sanchez, R.; Garay Reyes, C. G.; Muñoz Bolaños, Jairo Alberto; Cabrera Marrero, José M.; Hernandez Rivera, J. L. (2016-10)
Article
Accés obertThe powders of the AA 7075-ZrO2 were mixed by mechanical milling, but it was found that the system presents a few disadvantages when processed by conventional sintering and hot extrusion, since intermetallic phases between ... -
Constitutive model research of a TWIP steel processed by equal channel angular pressing
Wang, Lei; Benito Páramo, José Antonio; Calvo Muñoz, Jessica; Cabrera Marrero, José M. (2017-02)
Article
Accés restringit per política de l'editorialInfluence of equal channel angular pressing (ECAP) on mechanical properties of a TWIP steel was studied, and the tensile true stress-strain curves of the steel were fitted by Ludwik, Hollomon and Swift three kinds of ... -
Constitutive modeling of hot deformation of carbon steels in the intercritical zone
Jiménez Lugos, Juan Cancio; Cabrera Marrero, José M.; Chávez Alcalá, José Federico; Hallen López, José Manuel; López Rodríguez, Josué (2022-01-01)
Article
Accés obertA previous constitutive modeling for single-phase steels is extended using the mixing law to predict the behavior of hot deformation in the dual phase ferritic-austenitic intercritical zone of Fe-C-Mn-Si alloys. Mixing law ... -
Constitutive relationships for hot deformation of austenite
Mirzadeh, H.; Cabrera Marrero, José M.; Najafizadeh, A. (2011-09)
Article
Accés restringit per política de l'editorialConstitutive equations were used to derive the flow stress of a 17–4 PH stainless steel during hot compression testing. Two general methods were used: (i) a conventional method of finding apparent materials constants; and ... -
Critical strain for dynamic recrystallisation. The particular case of steel
Varela Castro, Gonzalo; Cabrera Marrero, José M.; Prado Pozuelo, José Manuel (Multidisciplinary Digital Publishing Institute (MDPI), 2020-01)
Article
Accés obertThe knowledge of the flow behavior of metallic alloys subjected to hot forming operations has particular interest for metallurgists in the practice of industrial forming processes involving high temperatures (e.g., rolling, ... -
Deformation heterogeneity study of a 6061-T6 aluminum alloy processed by equal channel angular pressing
Reyes Ruiz, Carlos; Figueroa, I. A.; Braham, C.; Cabrera Marrero, José M.; Zanellato, O.; Baiz, S.; Gonzalez, G. (2017-08)
Article
Accés obertAmong the severe plastic deformation techniques, the equal channel angular pressing (ECAP) has drastically improved the mechanical properties of the processed alloys. However, information regarding friction phenomenon, ... -
Design and development of complex phase steels with improved combination of strength and stretch-flangeability
Graux, Alexis; Cazottes, Sophie; de Castro Mazariegos, David; San Martín Fernández, David; Capdevila Montes, Carlos; Cabrera Marrero, José M.; Molas Busquets, Sílvia; Mirkovic, Bojana; Fabregue, Damien (Multidisciplinary Digital Publishing Institute (MDPI), 2020-06)
Article
Accés obertThis study presents the design and development of a hot-rolled bainitic steel, presenting a good combination of strength and stretch-flangeability, for automotive applications. Ti, Nb, and Mo were added in the steel ...